Transfusion system UMS-1-1 needle 0.8*40

The single-use universal medical transfusion-infusion system UMS-1-1 TU 64-05838972-5-93 is intended for intravenous administration of blood and its components, blood substitutes, solutions, and other transfusion media from glass and polymer containers with simultaneous administration of medicinal products approved for intravenous use. drugs. The infusion system, like the transfusion system, meets the requirements of TU 64-05838972-5-93. Its design solutions also take into account the requirements of GOST 25047-87 and ISO 8536-4. PERFORMANCE CHARACTERISTICS – The design of the two-channel polymer needle allows you to connect the system for infusion of infusion solutions both to rigid glass / polymer containers and to soft polymer containers. – The sharp tip allows you to easily pass into the rubber stopper of the bottle or into the fitting of the polymer container with the infusion medium, ensuring complete emptying of the container. – The air channel of the polymer needle is equipped with a hydrophobic membrane with a highly effective porosity for the speed of transfusion and bacterio-safe when air passes into the container. – Semi-rigid transparent drip chamber allows visualization of the dripping process. – The design of the drop forming element ensures the formation of 20 drops from (1.0±0.1) ml of distilled water at a flow rate of (50±5) drops per minute. – A cone-shaped filter installed in the chamber of the drip system ensures the removal of microparticles larger than 175 microns with a filtration coefficient of at least 80% when transfusing at least 1 liter of canned blood with a 10-14-day shelf life. – The roller clamp allows you to inject solutions at a given speed from drip to jet flow, choosing the most suitable for the patient. – The transparent wall of the tube avoids the possibility of air bubbles entering the patient’s venous bed. – The injection sleeve is designed for additional injections. The self-tightening of the coupling meets the requirements established by GOST 25047-87, ISO 8536-4, and allows you to enter up to 6 injections without loss of tightness. The coupling material is hypoallergenic synthetic polyisoprene. – The Luer connector is adapted to injection needles, peripheral and central venous catheters, other medical products with a similar port; – Sharp angle, double sharpening, thin wall provide painless and less traumatic injection needle insertion. – Protective caps on the polymer and injection needles ensure the sterility and apyrogenicity of the internal environment of the system. – Individual packaging consists of a contour-sealed bag of thermoformable multilayer film and gas-permeable paper, on which all information about the product is printed. – Sterilization is carried out with ethylene oxide in industrial sterilization chambers. TECHNICAL CHARACTERISTICS Product weight 50 g Product material medical polyvinyl chloride without phthalates (DEHP / DOP Free). Overall system length 1480 mm Injection needle diameter Luer diameter 0.8 mm (Product Code 361100) Diameter 1.2 mm (Product Code 361200) Air filter Available Air filter pore size with pore sizes up to 3 µm Injection solution filter Available Injection filter mesh size 175 µm solution Adjustment of the infusion rate Adjustment of the infusion rate using a white roller clamp Shelf life 3 years Ambient temperature during operation from +5 to +40 °C Strength 20 N adhesive joints Leak tightness 40 kPa at excess pressure in the internal cavity Sterilization gas sterilization with ethylene oxide (EO). Sterility, non-pyrogenicity, toxicity Sterile inside, non-pyrogenic, non-toxic Type of packaging Individual packaging, consisting of a thermoformed film and gas-permeable paper, interconnected along the contour by heat sealing Packaging Individual packaging The box is supplied in boxes, 100 pcs. in a box Instructions in Russian Availability of instructions in Russian Buy Transfusion system UMS-1-1 needle 0.8*40 Price for Transfusion system UMS-1-1 needle 0.8*40 needle 0.8*40